First thing this morning all the extra track turned up and I went straight out and fitted it all to the fiddle yard. I now consider that is the best I can do with KATO track system. During my learning on how to use the track I had assumed that they would produce various curved points! Sadly none could be found on any UK sites – so guess that they do not exist!

The final fiddle yard design finished, I made some between track templates based on the KATO point curved track supplied. Just to clarify, the middle six tracks are through tracks, the first and eighth tracks are sidings with a isolator halfway down each to hold two, two car DMUs etc.

The track will now be lifted and the backboard painted and glued down, after that the fiddle yard area will be corked. The track will then be relayed to the final design. I am looking to pin down the track if possible, if not I will have to investigate another way – we will see.

I had decided from day one of this project that I could not live with surface wiring and that all would be underboard. I also did not want to take the KATO point/power joiners off, I therefore investigated what was the smallest hole I could drill to allow the joiners to pass through, but still be out of sight and under the track. I think a 12mm or 13mm hole will do my wished for outcome.

At the moment I have not really decided on the viewable track at the front of the layout. I have had several ideas from friends including an extra curve in place to a few straights, a bi-directional passing loop or even a Stone Terminal. Whatever decided upon, the two main lines only will have overhead catenary.

Today I have been working on the scenic backboard, not an easy job with the rubbish wood I purchased from a large outlet. In the end I managed to get everything level on the backboard and also made a rear safety board to stop any fiddle yard accidents. I did have a few extra bits of track arrive today and they were duly put in place, the bulk of the extra track should arrive tomorrow.

The backboard is not glued down yet and will be painted both sides before fixing in place. Once glued in place I will temporarily take the track up and cork the whole fiddle yard.

My Son John came over to see us today and brought with him lots of his N Gauge stock so that we could test the track and check the fiddle yard capacity with the stock. We had an excellent morning and every rake fitted as we had hoped for and the running was excellent.

I must admit that the Kato track has many good points, but there are a few downsides as well. The fiddle yard area gives us six through tracks and four sidings, two on each circuit. The six main lines will hold up to an eleven car Pendolino and the sidings will hold two, two car DMUs each. So that will give us 10 made up trains, this is way short of what it could have held if we had used Peco N Gauge track. The good point is being well spaced helps with the removal and replacing of stock.

The reason we have used Kato is that we have amassed quite a lot over the last ten years at very modest prices, although I am now purchasing a few bits at full price to complete the layout.

Well there you are – the good and down sides of Kato, no ballasting the track, point motors enclosed and very easy wiring against far less storage in fiddle yard using the same area.

Now working on the backscene between the fiddle yard and the scenic section – watch this space.

Even although the layout is still to be corked, I just could not resist having a play with a potential track layout. This is the first time I have ever used KATO track so getting used to it seemed a good idea.

As the track is based on, but not a copy of the track between Ely Station and the North Junction, the main operational significance is that it is ‘Bi-Directional’ on both lines. There are no crossovers in this length of track giving each track its own fiddle yard in model form.

With the cork arriving next week it is just ‘play’ and things are bound to change. One of the main things I need to do is to get some stock and test the fiddle yard capacity. I also need to purchase a little more tracks to fill in the gaps.

The Baseboards for the N Gauge layout have now been put together in the Garage and on the newly extended trestles. I have decided to cork the whole layout after finding some good quality rolls on Ebay, it should arrive next week. This will be its home until finished.